"motorbike body parts"
Kabel speedometer CG125 kabel penggerak odometer sepeda motor kabel jarak tempuh transmisi presisi
CG125 speedometer cable for motorcycle odometer; custom-moulded 1:1 to match the original, with precise length, connector thread and routing curves, ready to install without modification; core made of high-carbon steel No. 70 (1×19 strand), tensile and wear resistant, not easy to break, accurate ...
CG125 Motorcycle Horn 12V Kualitas Tinggi Waterproof Horn
CG125 motorcycle horn; 12V DC driven, rated power 30W, volume up to 110-115dB, loud and clear sound with strong penetration, safer for riding alerts; fully sealed waterproof structure with ABS casing, dustproof, rainproof, ageing-resistant, suitable for complex riding environments such as rainy days ...
Tuas persneling sepeda motor CG125, pedal persneling terintegrasi yang dipertebal
CG125 motorcycle gear shift lever; the lever is made from 45# high-quality carbon steel forged in one piece, with a thickened design (14mm diameter), high strength, bend-resistant, difficult to break, and strong load-bearing capacity; the gear shift pedal head is made of anti-slip rubber with ...
Lengan ayun bawah sepeda motor CG125 paduan aluminium batang atas rakitan lengan ayun bawah mesin
CG125 rocker arm, rocker arm length 168mm, shaft hole diameter 18mm, mounting hole positions and rocker contact groove dimensions perfectly match the original engine cylinder block and rocker, allowing direct replacement without modification, suitable for 125cc single-cylinder pushrod engine valve ...
Set Jari-Jari Roda Depan dan Belakang CG125 Baja Galvanis, Jari-Jari Velg, Mur
CG125 front and rear wheel spoke set, front spoke specifications 3×175MM, rear spoke 3.7×175MM, holes perfectly match CG125 front and rear rims and hubs; made of high-quality galvanized steel, cold drawn and formed, tempered with Japanese technology, tensile strength ≥600MPa, stable load-bearing and ...
CG125 set roda depan 1.4×18 inci rim hub berbicara
CG125 front wheel assembly, size 1.4×18 inches, the hole position and axle diameter perfectly match the CG125 front axle; uses Japanese cold-pressed rim, high-precision hub, and galvanised spokes, with the rim roundness pre-calibrated before leaving the factory (error ≤1mm), ready to install, saving ...
Roda belakang CG125 rakitan pelek 1.6×18 inci, hub, set jeruji
CG125 rear wheel assembly, size 1.6×18 inches, axle diameter and sprocket mounting position perfectly match CG125 rear axle and transmission system, compatible with Honda CG125, Pearl 125 and other 125cc pushrod models, can directly replace the original rear wheel without modification; made with ...
CG125 set penutup sisi mesin CDI merah dekoratif penutup bagian dalam
CG125 engine side cover, the mounting holes and clips match the CG125 engine case 1:1, suitable for Honda CG125, Pearl River 125 and other 125cc overhead valve models, directly replacing the original engine side cover; includes red exterior cover and white inner cover, the exterior cover is made of ...
Spakbor depan CG125, spatbor melengkung krom mengkilap, kompatibel dengan spatbor roda depan top-rod 125
CG125 front fender with a glossy chrome curved water shield, the curved dimensions perfectly fit the CG125 front wheel rim, and the mounting holes match the front fork bracket 1:1; made of thickened steel plate with a glossy chrome finish, salt spray test ≥120 hours, long-term use in rainy or muddy ...
Spakbor belakang CG125, pelindung air melengkung krom mengkilap, kompatibel dengan spakbor roda belakang mesin 125 pushrod
CG125 rear mudguard, with an arched size perfectly fitting the CG125 rear wheel rim, installation holes matching the rear fork bracket 1:1; made of thickened steel plate with mirror chrome plating, salt spray test ≥120 hours, long-term use in rainy and muddy conditions without rusting, the glossy ...
Bagian tengah spakbor CG125 hitam ABS, penutup penghubung spakbor belakang cocok untuk bagian tengah spakbor roda belakang sepeda motor 125 top-bar
The CG125 middle fender section matches the installation clips and connecting grooves with the upper and lower sections of the CG125 rear fender 1:1, allowing direct replacement of the original middle fender without modification. It is made of high-strength ABS engineering plastic through injection ...
CG125 rearview mirror assembly round reflective mirror chrome bracket set compatible with 125 top rod motorcycle head reverse mirror
CG125 motorcycle rearview mirror assembly, threaded interface (M8) matches 1:1 with CG125 handlebar mounting holes, compatible with Honda CG125, Pearl River 125 and other 125cc pushrod engine models, directly replaces the original mirrors without modification; silver-reflective glass, clear ...
