"motorbike body parts"
Cáp đồng hồ tốc độ CG125, cáp dẫn động đồng hồ đo quãng đường xe máy, cáp đo dặm truyền động chính xác
CG125 speedometer cable for motorcycle odometer; custom-moulded 1:1 to match the original, with precise length, connector thread and routing curves, ready to install without modification; core made of high-carbon steel No. 70 (1×19 strand), tensile and wear resistant, not easy to break, accurate ...
Còi xe máy CG125 12V Còi chống nước chất lượng cao
CG125 motorcycle horn; 12V DC driven, rated power 30W, volume up to 110-115dB, loud and clear sound with strong penetration, safer for riding alerts; fully sealed waterproof structure with ABS casing, dustproof, rainproof, ageing-resistant, suitable for complex riding environments such as rainy days ...
CG125 đòn bẩy chuyển số xe máy, bàn đạp bánh răng tích hợp dày hơn
CG125 motorcycle gear shift lever; the lever is made from 45# high-quality carbon steel forged in one piece, with a thickened design (14mm diameter), high strength, bend-resistant, difficult to break, and strong load-bearing capacity; the gear shift pedal head is made of anti-slip rubber with ...
Cần đẩy trên bằng hợp kim nhôm của xe máy CG125, cụm cần đẩy dưới của động cơ
CG125 rocker arm, rocker arm length 168mm, shaft hole diameter 18mm, mounting hole positions and rocker contact groove dimensions perfectly match the original engine cylinder block and rocker, allowing direct replacement without modification, suitable for 125cc single-cylinder pushrod engine valve ...
CG125 Đặt bánh xe phía trước và phía sau ốp ốp ốp thép nhựa
CG125 front and rear wheel spoke set, front spoke specifications 3×175MM, rear spoke 3.7×175MM, holes perfectly match CG125 front and rear rims and hubs; made of high-quality galvanized steel, cold drawn and formed, tempered with Japanese technology, tensile strength ≥600MPa, stable load-bearing and ...
CG125 bộ lắp ráp bánh trước 1.4 × 18 inch rim hub set
CG125 front wheel assembly, size 1.4×18 inches, the hole position and axle diameter perfectly match the CG125 front axle; uses Japanese cold-pressed rim, high-precision hub, and galvanised spokes, with the rim roundness pre-calibrated before leaving the factory (error ≤1mm), ready to install, saving ...
Bộ vành sau CG125 1.6×18 inch, bộ căm và moay ơ
CG125 rear wheel assembly, size 1.6×18 inches, axle diameter and sprocket mounting position perfectly match CG125 rear axle and transmission system, compatible with Honda CG125, Pearl 125 and other 125cc pushrod models, can directly replace the original rear wheel without modification; made with ...
CG125 bộ phủ bên động cơ CDI phủ trang trí màu đỏ
CG125 engine side cover, the mounting holes and clips match the CG125 engine case 1:1, suitable for Honda CG125, Pearl River 125 and other 125cc overhead valve models, directly replacing the original engine side cover; includes red exterior cover and white inner cover, the exterior cover is made of ...
CG125 vạt phía trước, bảo vệ bùn cong chrome bóng, tương thích với 125 vạt bánh xe phía trước
CG125 front fender with a glossy chrome curved water shield, the curved dimensions perfectly fit the CG125 front wheel rim, and the mounting holes match the front fork bracket 1:1; made of thickened steel plate with a glossy chrome finish, salt spray test ≥120 hours, long-term use in rainy or muddy ...
CG125 bảo vệ bùn phía sau, chống nước cong chrome bóng, tương thích với 125 động cơ đẩy
CG125 rear mudguard, with an arched size perfectly fitting the CG125 rear wheel rim, installation holes matching the rear fork bracket 1:1; made of thickened steel plate with mirror chrome plating, salt spray test ≥120 hours, long-term use in rainy and muddy conditions without rusting, the glossy ...
Phần giữa chắn bùn CG125 màu đen ABS, nắp nối chắn bùn sau phù hợp cho phần giữa chắn bùn bánh sau xe máy 125 gác-ba
The CG125 middle fender section matches the installation clips and connecting grooves with the upper and lower sections of the CG125 rear fender 1:1, allowing direct replacement of the original middle fender without modification. It is made of high-strength ABS engineering plastic through injection ...
Cụm gương chiếu hậu CG125 gương phản xạ tròn giá đỡ mạ crôm bộ tương thích với đầu xe máy 125 cần trên gương chiếu hậu
CG125 motorcycle rearview mirror assembly, threaded interface (M8) matches 1:1 with CG125 handlebar mounting holes, compatible with Honda CG125, Pearl River 125 and other 125cc pushrod engine models, directly replaces the original mirrors without modification; silver-reflective glass, clear ...
