"motorcycle components"
YBR125 motorcycle brake light line assembly brake signal trigger switch assembly
YBR125 motorcycle brake light wire assembly, switch interface, wire harness specifications and the original brake system fully match, direct replacement without adjusting the circuit; Including brake light switch, wire harness, spring and hook, one-stop replacement of brake signal components, save ...
YBR125 Motorcycle carburetor repair kit Carburetor seal adjustment kit set
YBR125 motorcycle carburetor repair kit, parts specifications, seal size and YBR125 carburetor fully match, directly replace the original parts without adjustment; Including gasket, oil needle, screw, spring, snap and other full set of maintenance accessories, covering the common carburettor fault ...
YBR125 motorcycle spark plug CR6HSA resistance type M10*12.7mm ignition unit
YBR125 motorcycle spark plug, thread specification (M10*12.7mm) and calorific value (CR6HSA) fully match YBR125 engine, direct replacement without adjustment; Built-in resistance element, effectively suppress electromagnetic interference, avoid affecting the vehicle circuit and electronic equipment; ...
YBR125 Motorcycle valve guide Package Cylinder head valve guide unit (including seal ring)
YBR125 motorcycle valve tube set, total length 31.5MM, outer diameter 11MM, aperture 5MM and the original car valve hole completely match, direct replacement without ream/shrinkage hole; With valve tube sealing ring, one-stop solution to guide + sealing needs, save the trouble of purchasing seals ...
CG125 motorcycle left and right switch assembly, combined control switch, suitable for 125 push-rod motorcycle handlebar control switch
CG125 motorcycle left and right switch assembly, including left switch (clutch/indicator/horn) and right switch (throttle/start/light), with mounting holes and wiring interfaces matching the CG125 handlebar and electrical system 1:1. Suitable for Honda CG125, Pearl River 125 and other 125cc overhead ...
CG125 motorcycle handle rubber non-skid throttle grip sleeve is adapted to 125 top bar motorcycle handle parts
CG125 motorcycle handlebar rubber, the inner diameter, length and CG125 handlebar, throttle turn completely match, suitable for Honda CG125, Pearl River 125 and other top rod scooter type, directly into the handlebar can be used, without modification; The surface adopts dense stripe + particle anti...
YBR125 motorcycle big tooth screw set slink wheel fixed splint + bolt
YBR125 motorcycle big tooth screw set, splint hole position, screw specifications and the original car big tooth (sket) completely match, directly replace the original fixed parts without adjusting the installation position; The splint is made of rust-proof galvanized steel plate, and the screws are ...
CG series Motorcycle oil Switch Fuel tank oil control valve (oil level display rod)
CG series motorcycle oil switch, interface specifications, installation size and CG series fuel tank fully match, directly replace the oil switch without adjusting the installation position; Support "ON (main oil) -RES (standby oil) -OFF" gear switch, precise control of fuel output, suitable for ...
CG125 Motorcycle Main Stand Shaft 40Cr Alloy Steel Main Support Pivot
Common specifications for the CG125 motorcycle main stand shaft are 17×141mm (diameter × length). The mounting holes perfectly match the frame and the main stand bracket, allowing direct replacement without modification and ensuring precise alignment of the support structure. Made from premium 40Cr ...
CG125 motorcycle brake pedal spring 65 manganese steel rear foot brake return spring
CG125 motorcycle brake pedal spring, with hook pitch and wire diameter perfectly matching the original vehicle holes, can be replaced directly without modification; made of 65 manganese spring steel cold-rolled, quenched and tempered, with a stable elastic coefficient (rebound rate ≥98%), fatigue ...
CG125 motorcycle air filter assembly air filter suitable for 125 pushrod engine intake filtration
CG125 motorcycle air filter assembly, with installation clips and intake interface matching the CG125 engine intake and frame 1:1, suitable for Honda CG125, Pearl River 125 and other 125cc pushrod engines, directly replacing the original air filter without modification; equipped with a high-density ...
CG125 Motorcycle Spark Plug D8TC Model Suitable for 125 Overhead Cam Engine Ignition Part
CG125 motorcycle spark plug, thread size (M12×1.25), heat range (D8TC) matches the CG125 engine ignition system 1:1, suitable for Honda CG125, Pearl River 125 and other 125cc push-rod engine models, directly replacing the original spark plug without adjustment; the electrode is made of iridium...
