"motorcycle components"
Conjunto de cableado de luz de freno de motocicleta YBR125, conjunto de interruptor de activación de señal de freno
YBR125 motorcycle brake light wire assembly, switch interface, wire harness specifications and the original brake system fully match, direct replacement without adjusting the circuit; Including brake light switch, wire harness, spring and hook, one-stop replacement of brake signal components, save ...
YBR125 Kit de reparación del carburador de motocicleta Kit de ajuste del sello del carburador
YBR125 motorcycle carburetor repair kit, parts specifications, seal size and YBR125 carburetor fully match, directly replace the original parts without adjustment; Including gasket, oil needle, screw, spring, snap and other full set of maintenance accessories, covering the common carburettor fault ...
Unidad de encendido de tipo M10*12,7 mm de resistencia CR6HSA de la bujía de la motocicleta YBR125
YBR125 motorcycle spark plug, thread specification (M10*12.7mm) and calorific value (CR6HSA) fully match YBR125 engine, direct replacement without adjustment; Built-in resistance element, effectively suppress electromagnetic interference, avoid affecting the vehicle circuit and electronic equipment; ...
Guía de válvula de motocicleta YBR125 Paquete Guía de válvula de culata (incluyendo anillo de sellado)
YBR125 motorcycle valve tube set, total length 31.5MM, outer diameter 11MM, aperture 5MM and the original car valve hole completely match, direct replacement without ream/shrinkage hole; With valve tube sealing ring, one-stop solution to guide + sealing needs, save the trouble of purchasing seals ...
Conjunto de interruptores izquierdo y derecho para motocicleta CG125, interruptor de control combinado, adecuado para interruptor de control de manillar de motocicleta de varilla de empuje 125
CG125 motorcycle left and right switch assembly, including left switch (clutch/indicator/horn) and right switch (throttle/start/light), with mounting holes and wiring interfaces matching the CG125 handlebar and electrical system 1:1. Suitable for Honda CG125, Pearl River 125 and other 125cc overhead ...
CG125 manija de motocicleta de caucho antiderrapante manguera de agarre del acelerador está adaptado a 125 partes de manija de la barra superior de la motocicleta
CG125 motorcycle handlebar rubber, the inner diameter, length and CG125 handlebar, throttle turn completely match, suitable for Honda CG125, Pearl River 125 and other top rod scooter type, directly into the handlebar can be used, without modification; The surface adopts dense stripe + particle anti...
Juego de tornillos de diente grande para motocicleta YBR125, rueda slink, férula fija + perno
YBR125 motorcycle big tooth screw set, splint hole position, screw specifications and the original car big tooth (sket) completely match, directly replace the original fixed parts without adjusting the installation position; The splint is made of rust-proof galvanized steel plate, and the screws are ...
Serial CG Conmutador de aceite de motocicleta Válvula de control de aceite del tanque de combustible (varilla de visualización del nivel de aceite)
CG series motorcycle oil switch, interface specifications, installation size and CG series fuel tank fully match, directly replace the oil switch without adjusting the installation position; Support "ON (main oil) -RES (standby oil) -OFF" gear switch, precise control of fuel output, suitable for ...
Eje principal del soporte de la motocicleta CG125, acero de aleación 40Cr, pivote de soporte principal
Common specifications for the CG125 motorcycle main stand shaft are 17×141mm (diameter × length). The mounting holes perfectly match the frame and the main stand bracket, allowing direct replacement without modification and ensuring precise alignment of the support structure. Made from premium 40Cr ...
Resorte del pedal de freno de motocicleta CG125, acero al manganeso 65, resorte de retorno del freno trasero
CG125 motorcycle brake pedal spring, with hook pitch and wire diameter perfectly matching the original vehicle holes, can be replaced directly without modification; made of 65 manganese spring steel cold-rolled, quenched and tempered, with a stable elastic coefficient (rebound rate ≥98%), fatigue ...
Conjunto de filtro de aire para motocicleta CG125, filtro de aire adecuado para la filtración de admisión del motor de varilla de empuje 125
CG125 motorcycle air filter assembly, with installation clips and intake interface matching the CG125 engine intake and frame 1:1, suitable for Honda CG125, Pearl River 125 and other 125cc pushrod engines, directly replacing the original air filter without modification; equipped with a high-density ...
Bujía de motocicleta CG125 modelo D8TC adecuada para motor de 125 con árbol de levas en cabeza, pieza de encendido
CG125 motorcycle spark plug, thread size (M12×1.25), heat range (D8TC) matches the CG125 engine ignition system 1:1, suitable for Honda CG125, Pearl River 125 and other 125cc push-rod engine models, directly replacing the original spark plug without adjustment; the electrode is made of iridium...
