"motorcycle components"
YBR125 bộ phận dây dẫn đèn phanh xe máy bộ phận công tắc kích hoạt tín hiệu phanh
YBR125 motorcycle brake light wire assembly, switch interface, wire harness specifications and the original brake system fully match, direct replacement without adjusting the circuit; Including brake light switch, wire harness, spring and hook, one-stop replacement of brake signal components, save ...
YBR125 Bộ sửa chữa khí đốt xe máy Bộ điều chỉnh niêm phong khí đốt
YBR125 motorcycle carburetor repair kit, parts specifications, seal size and YBR125 carburetor fully match, directly replace the original parts without adjustment; Including gasket, oil needle, screw, spring, snap and other full set of maintenance accessories, covering the common carburettor fault ...
YBR125 máy móc cắm tia lửa CR6HSA kháng cự loại M10 * 12,7mm đơn vị thắp sáng
YBR125 motorcycle spark plug, thread specification (M10*12.7mm) and calorific value (CR6HSA) fully match YBR125 engine, direct replacement without adjustment; Built-in resistance element, effectively suppress electromagnetic interference, avoid affecting the vehicle circuit and electronic equipment; ...
YBR125 Hướng dẫn van xe máy Gói Đơn vị hướng dẫn van đầu xi lanh (bao gồm vòng niêm phong)
YBR125 motorcycle valve tube set, total length 31.5MM, outer diameter 11MM, aperture 5MM and the original car valve hole completely match, direct replacement without ream/shrinkage hole; With valve tube sealing ring, one-stop solution to guide + sealing needs, save the trouble of purchasing seals ...
Cụm công tắc trái và phải xe máy CG125, công tắc điều khiển kết hợp, phù hợp với công tắc điều khiển tay lái xe máy 125 cần đẩy
CG125 motorcycle left and right switch assembly, including left switch (clutch/indicator/horn) and right switch (throttle/start/light), with mounting holes and wiring interfaces matching the CG125 handlebar and electrical system 1:1. Suitable for Honda CG125, Pearl River 125 and other 125cc overhead ...
Ống bọc tay nắm ga chống trượt cao su xe máy CG125 được điều chỉnh cho các bộ phận tay lái xe máy 125
CG125 motorcycle handlebar rubber, the inner diameter, length and CG125 handlebar, throttle turn completely match, suitable for Honda CG125, Pearl River 125 and other top rod scooter type, directly into the handlebar can be used, without modification; The surface adopts dense stripe + particle anti...
Bộ ốc răng lớn xe máy YBR125 cố định bánh răng + bu lông
YBR125 motorcycle big tooth screw set, splint hole position, screw specifications and the original car big tooth (sket) completely match, directly replace the original fixed parts without adjusting the installation position; The splint is made of rust-proof galvanized steel plate, and the screws are ...
CG series Motorcycle oil switch Fuel tank oil control valve (đường hiển thị mức dầu)
CG series motorcycle oil switch, interface specifications, installation size and CG series fuel tank fully match, directly replace the oil switch without adjusting the installation position; Support "ON (main oil) -RES (standby oil) -OFF" gear switch, precise control of fuel output, suitable for ...
CG125 Motorcycle Main Stand Shaft 40Cr hợp kim thép chính hỗ trợ pivot
Common specifications for the CG125 motorcycle main stand shaft are 17×141mm (diameter × length). The mounting holes perfectly match the frame and the main stand bracket, allowing direct replacement without modification and ensuring precise alignment of the support structure. Made from premium 40Cr ...
CG125 đạp phanh xe máy mùa xuân 65 thép mangan phía sau chân phanh trở lại mùa xuân
CG125 motorcycle brake pedal spring, with hook pitch and wire diameter perfectly matching the original vehicle holes, can be replaced directly without modification; made of 65 manganese spring steel cold-rolled, quenched and tempered, with a stable elastic coefficient (rebound rate ≥98%), fatigue ...
Cụm lọc gió xe máy CG125, lọc gió phù hợp cho động cơ 125 đũa đẩy, lọc khí nạp
CG125 motorcycle air filter assembly, with installation clips and intake interface matching the CG125 engine intake and frame 1:1, suitable for Honda CG125, Pearl River 125 and other 125cc pushrod engines, directly replacing the original air filter without modification; equipped with a high-density ...
CG125 Máy móc motor Spark Plug D8TC Mô hình phù hợp với 125 Overhead Cam Engine Ignition Part
CG125 motorcycle spark plug, thread size (M12×1.25), heat range (D8TC) matches the CG125 engine ignition system 1:1, suitable for Honda CG125, Pearl River 125 and other 125cc push-rod engine models, directly replacing the original spark plug without adjustment; the electrode is made of iridium...
