"motorcycle body accessories"
CG125 silnik startowy 12V 0,8KW odpowiedni dla Honda CG125, Zhuhai ZJ125, Xingfu XF125 125cc silnik startowy motocykli
The CG125 motor (starter motor) is the core component of the engine starting system. It drives the rotor to rotate via 12V DC power and drives the engine crankshaft through a reduction gear to achieve cold or hot engine starting. It is compatible with the Honda CG125 and Zhuhai ZJ125, Xingfu XF125, ...
CG125 RPM Cable Motorcycle Tachometer Cable Mechanical RPM Cable
CG125 speed line motorcycle tachometer cable, precise transmission speed cable; the core is made of No.70 high carbon steel (multi-strand twisted), tensile and wear-resistant, not easy to break, stable transmission torque; zinc alloy gear joint, steel universal joint, die-cast without air holes, ...
CG125 kablometr prędkości, kablometr jazdy motocykla, precyzyjny przewóz, przebieg kablu
CG125 speedometer cable for motorcycle odometer; custom-moulded 1:1 to match the original, with precise length, connector thread and routing curves, ready to install without modification; core made of high-carbon steel No. 70 (1×19 strand), tensile and wear resistant, not easy to break, accurate ...
Dolny wahacz motocykla CG125, stop aluminium, górny drążek, dolny wahacz silnika, zespół
CG125 rocker arm, rocker arm length 168mm, shaft hole diameter 18mm, mounting hole positions and rocker contact groove dimensions perfectly match the original engine cylinder block and rocker, allowing direct replacement without modification, suitable for 125cc single-cylinder pushrod engine valve ...
CG125 Wał przesuwny trójczęściowy zestaw 41 Zębów Górnej Prędkości Rdzenia Wał przesuwny most Zęby Wał przesuwny Kompatybilny z motocyklami 125/150
The CG125 camshaft three-piece kit is a dedicated maintenance/replacement kit for the rocker arm-type valve mechanism, integrating the camshaft, bridge gear, rocker shaft and seals. It is used to address issues such as camshaft wear and valve timing disorders, and is compatible with the Honda CG125 ...
CG125 Środkowa sekcja błotnika czarny ABS tylna pokrywa złącza błotnika odpowiednia dla 125 górnej pręty motocykla tylne koło błotnika środkowa sekcja
The CG125 middle fender section matches the installation clips and connecting grooves with the upper and lower sections of the CG125 rear fender 1:1, allowing direct replacement of the original middle fender without modification. It is made of high-strength ABS engineering plastic through injection ...
Zawór CG125, oryginalna specyfikacja fabryczna, pasuje ciasno do gniazda zaworu
The CG125 uses a single-cylinder, two-valve (1 intake, 1 exhaust) OHV (overhead valve with pushrod) valve mechanism. The valve assembly is the core of the engine's valve system, responsible for accurately opening and closing the intake and exhaust channels according to the engine cycle, ensuring the ...
Zestaw cylindrów CG125, podstawowy zestaw silnika czterotakowego o chłodzonym powietrzem jednocylindrowym
The CG125 cylinder set is the core assembly of a single-cylinder, four-stroke, air-cooled engine, used in 125cc commuter motorcycles. It consists of a cylinder body, piston, piston rings, piston pin, circlip, and upper and lower gaskets, responsible for completing the four-stroke cycle of intake, ...
Sprzęgło 5-odrukowe z 6 płytkami dla modelu CG125
5-hole 6-plate clutch for CG125 model High-performance 5-hole 6-plate clutch assembly specifically designed for CG125 motorcycle models. This precision-engineered component ensures optimal power transfer and durability. 5-hole mounting pattern for secure installation 6-plate design for enhanced ...
Zestaw tylnego koła CG125, obręcz 1.6×18 cali, piasta, szprychy
CG125 rear wheel assembly, size 1.6×18 inches, axle diameter and sprocket mounting position perfectly match CG125 rear axle and transmission system, compatible with Honda CG125, Pearl 125 and other 125cc pushrod models, can directly replace the original rear wheel without modification; made with ...
Zestaw piasty przedniego koła CG125, aluminiowa piasta przedniego koła, kompatybilna z maszyną 125 Top Rod, piasta szprych przedniego koła
CG125 front wheel hub assembly, with axle hole dimensions and spoke hole positions matching the CG125 front axle and rim 1:1, suitable for Honda CG125, Zhujian 125 and other 125cc push-rod engine models, directly replacing the original front wheel hub without modifications; made of high-strength die...
Zestaw koła przedniego CG125, obręcz 1,4x18 cali, piasta, szprychy
CG125 front wheel assembly, size 1.4×18 inches, the hole position and axle diameter perfectly match the CG125 front axle; uses Japanese cold-pressed rim, high-precision hub, and galvanised spokes, with the rim roundness pre-calibrated before leaving the factory (error ≤1mm), ready to install, saving ...
