"motorcycle body accessories"
Đề pa CG125 12V 0.8KW phù hợp cho Honda CG125, Zhuhai ZJ125, Xingfu XF125 động cơ khởi động xe máy 125cc
The CG125 motor (starter motor) is the core component of the engine starting system. It drives the rotor to rotate via 12V DC power and drives the engine crankshaft through a reduction gear to achieve cold or hot engine starting. It is compatible with the Honda CG125 and Zhuhai ZJ125, Xingfu XF125, ...
CG125 RPM Cable Xe máy máy tính tốc độ Cable Mechanical RPM Cable
CG125 speed line motorcycle tachometer cable, precise transmission speed cable; the core is made of No.70 high carbon steel (multi-strand twisted), tensile and wear-resistant, not easy to break, stable transmission torque; zinc alloy gear joint, steel universal joint, die-cast without air holes, ...
Cáp đồng hồ tốc độ CG125, cáp dẫn động đồng hồ đo quãng đường xe máy, cáp đo dặm truyền động chính xác
CG125 speedometer cable for motorcycle odometer; custom-moulded 1:1 to match the original, with precise length, connector thread and routing curves, ready to install without modification; core made of high-carbon steel No. 70 (1×19 strand), tensile and wear resistant, not easy to break, accurate ...
Cần đẩy trên bằng hợp kim nhôm của xe máy CG125, cụm cần đẩy dưới của động cơ
CG125 rocker arm, rocker arm length 168mm, shaft hole diameter 18mm, mounting hole positions and rocker contact groove dimensions perfectly match the original engine cylinder block and rocker, allowing direct replacement without modification, suitable for 125cc single-cylinder pushrod engine valve ...
CG125 Camshaft Ba phần Set 41 Tooth Top Push Rod Camshaft Bridge Teeth Rocker Shaft tương thích với xe máy 125/150
The CG125 camshaft three-piece kit is a dedicated maintenance/replacement kit for the rocker arm-type valve mechanism, integrating the camshaft, bridge gear, rocker shaft and seals. It is used to address issues such as camshaft wear and valve timing disorders, and is compatible with the Honda CG125 ...
Phần giữa chắn bùn CG125 màu đen ABS, nắp nối chắn bùn sau phù hợp cho phần giữa chắn bùn bánh sau xe máy 125 gác-ba
The CG125 middle fender section matches the installation clips and connecting grooves with the upper and lower sections of the CG125 rear fender 1:1, allowing direct replacement of the original middle fender without modification. It is made of high-strength ABS engineering plastic through injection ...
van CG125, đặc điểm kỹ thuật nhà máy gốc, phù hợp chặt chẽ với vòng ghế van
The CG125 uses a single-cylinder, two-valve (1 intake, 1 exhaust) OHV (overhead valve with pushrod) valve mechanism. The valve assembly is the core of the engine's valve system, responsible for accurately opening and closing the intake and exhaust channels according to the engine cycle, ensuring the ...
Bộ xi lanh CG125, bộ lõi của một động cơ bốn nhịp lạnh bằng không khí một xi lanh
The CG125 cylinder set is the core assembly of a single-cylinder, four-stroke, air-cooled engine, used in 125cc commuter motorcycles. It consists of a cylinder body, piston, piston rings, piston pin, circlip, and upper and lower gaskets, responsible for completing the four-stroke cycle of intake, ...
Máy ly hợp 5 lỗ 6 tấm cho mô hình CG125
5-hole 6-plate clutch for CG125 model High-performance 5-hole 6-plate clutch assembly specifically designed for CG125 motorcycle models. This precision-engineered component ensures optimal power transfer and durability. 5-hole mounting pattern for secure installation 6-plate design for enhanced ...
Bộ vành sau CG125 1.6×18 inch, bộ căm và moay ơ
CG125 rear wheel assembly, size 1.6×18 inches, axle diameter and sprocket mounting position perfectly match CG125 rear axle and transmission system, compatible with Honda CG125, Pearl 125 and other 125cc pushrod models, can directly replace the original rear wheel without modification; made with ...
Cụm moay ơ bánh trước CG125 Bằng nhôm Moay ơ bánh trước tương thích với máy 125 thanh giằng trên Moay ơ nan hoa bánh trước
CG125 front wheel hub assembly, with axle hole dimensions and spoke hole positions matching the CG125 front axle and rim 1:1, suitable for Honda CG125, Zhujian 125 and other 125cc push-rod engine models, directly replacing the original front wheel hub without modifications; made of high-strength die...
CG125 bộ lắp ráp bánh trước 1.4 × 18 inch rim hub set
CG125 front wheel assembly, size 1.4×18 inches, the hole position and axle diameter perfectly match the CG125 front axle; uses Japanese cold-pressed rim, high-precision hub, and galvanised spokes, with the rim roundness pre-calibrated before leaving the factory (error ≤1mm), ready to install, saving ...
