"motorcycle body accessories"
CG125 시동 모터 12V 0.8KW, Honda CG125, Zhuhai ZJ125, Xingfu XF125 125cc 오토바이 시동 모터에 적합
The CG125 motor (starter motor) is the core component of the engine starting system. It drives the rotor to rotate via 12V DC power and drives the engine crankshaft through a reduction gear to achieve cold or hot engine starting. It is compatible with the Honda CG125 and Zhuhai ZJ125, Xingfu XF125, ...
CG125 RPM 케이블 오토바이 타코미터 케이블 기계식 RPM 케이블
CG125 speed line motorcycle tachometer cable, precise transmission speed cable; the core is made of No.70 high carbon steel (multi-strand twisted), tensile and wear-resistant, not easy to break, stable transmission torque; zinc alloy gear joint, steel universal joint, die-cast without air holes, ...
CG125 속도 측정 케이블 오토바이 오도 미터 드라이브 케이블 정밀 전송 마일리지 케이블
CG125 speedometer cable for motorcycle odometer; custom-moulded 1:1 to match the original, with precise length, connector thread and routing curves, ready to install without modification; core made of high-carbon steel No. 70 (1×19 strand), tensile and wear resistant, not easy to break, accurate ...
CG125 오토바이 로커 암 하부 알루미늄 합금 상단 로드 엔진 로커 암 하부 어셈블리
CG125 rocker arm, rocker arm length 168mm, shaft hole diameter 18mm, mounting hole positions and rocker contact groove dimensions perfectly match the original engine cylinder block and rocker, allowing direct replacement without modification, suitable for 125cc single-cylinder pushrod engine valve ...
CG125 캠샤프트 3피스 세트 41T 상단 푸시 로드 캠샤프트 브리지 기어 로커 샤프트 125/150 오토바이 호환
The CG125 camshaft three-piece kit is a dedicated maintenance/replacement kit for the rocker arm-type valve mechanism, integrating the camshaft, bridge gear, rocker shaft and seals. It is used to address issues such as camshaft wear and valve timing disorders, and is compatible with the Honda CG125 ...
CG125 진흙 보호 중앙 섹션 검은 ABS 후면 진흙 보호 연결 덮개 125 최고 바 오토바이 후기 바퀴 진흙 보호 중앙 섹션에 적합
The CG125 middle fender section matches the installation clips and connecting grooves with the upper and lower sections of the CG125 rear fender 1:1, allowing direct replacement of the original middle fender without modification. It is made of high-strength ABS engineering plastic through injection ...
CG125 밸브, 원본 공장 사양, 밸브 좌석 반지와 잘 어울립니다
The CG125 uses a single-cylinder, two-valve (1 intake, 1 exhaust) OHV (overhead valve with pushrod) valve mechanism. The valve assembly is the core of the engine's valve system, responsible for accurately opening and closing the intake and exhaust channels according to the engine cycle, ensuring the ...
CG125 실린더 세트, 단기통 4행정 공랭식 엔진의 핵심 부품
The CG125 cylinder set is the core assembly of a single-cylinder, four-stroke, air-cooled engine, used in 125cc commuter motorcycles. It consists of a cylinder body, piston, piston rings, piston pin, circlip, and upper and lower gaskets, responsible for completing the four-stroke cycle of intake, ...
CG125 모델용 5홀 6판 클러치
5-hole 6-plate clutch for CG125 model High-performance 5-hole 6-plate clutch assembly specifically designed for CG125 motorcycle models. This precision-engineered component ensures optimal power transfer and durability. 5-hole mounting pattern for secure installation 6-plate design for enhanced ...
CG125 리어 휠 어셈블리 1.6×18인치 림 허브 스포크 세트
CG125 rear wheel assembly, size 1.6×18 inches, axle diameter and sprocket mounting position perfectly match CG125 rear axle and transmission system, compatible with Honda CG125, Pearl 125 and other 125cc pushrod models, can directly replace the original rear wheel without modification; made with ...
CG125 앞바퀴 허브 조립 알루미늄 앞바퀴 허브 125 톱 스드 머신과 호환
CG125 front wheel hub assembly, with axle hole dimensions and spoke hole positions matching the CG125 front axle and rim 1:1, suitable for Honda CG125, Zhujian 125 and other 125cc push-rod engine models, directly replacing the original front wheel hub without modifications; made of high-strength die...
CG125 앞바퀴 어셈블리 1.4×18인치 림 허브 스포크 세트
CG125 front wheel assembly, size 1.4×18 inches, the hole position and axle diameter perfectly match the CG125 front axle; uses Japanese cold-pressed rim, high-precision hub, and galvanised spokes, with the rim roundness pre-calibrated before leaving the factory (error ≤1mm), ready to install, saving ...
