"motorcycle body accessories"
CG125 स्टार्टर मोटर 12V 0.8KW होंडा CG125, Zhuhai ZJ125, Xingfu XF125 125cc मोटरसाइकिल स्टार्टर मोटर के लिए उपयुक्त
The CG125 motor (starter motor) is the core component of the engine starting system. It drives the rotor to rotate via 12V DC power and drives the engine crankshaft through a reduction gear to achieve cold or hot engine starting. It is compatible with the Honda CG125 and Zhuhai ZJ125, Xingfu XF125, ...
CG125 आरपीएम केबल मोटरसाइकिल टैकोमीटर केबल मैकेनिकल आरपीएम केबल
CG125 speed line motorcycle tachometer cable, precise transmission speed cable; the core is made of No.70 high carbon steel (multi-strand twisted), tensile and wear-resistant, not easy to break, stable transmission torque; zinc alloy gear joint, steel universal joint, die-cast without air holes, ...
CG125 स्पीडोमीटर केबल मोटरसाइकिल ओडोमीटर ड्राइव केबल सटीक ट्रांसमिशन माइलेज केबल
CG125 speedometer cable for motorcycle odometer; custom-moulded 1:1 to match the original, with precise length, connector thread and routing curves, ready to install without modification; core made of high-carbon steel No. 70 (1×19 strand), tensile and wear resistant, not easy to break, accurate ...
CG125 मोटरसाइकिल लोअर रॉकर आर्म एल्यूमीनियम मिश्र धातु टॉप रॉड इंजन लोअर रॉकर आर्म संयोजन
CG125 rocker arm, rocker arm length 168mm, shaft hole diameter 18mm, mounting hole positions and rocker contact groove dimensions perfectly match the original engine cylinder block and rocker, allowing direct replacement without modification, suitable for 125cc single-cylinder pushrod engine valve ...
CG125 कैंषफ़्ट तीन-टुकड़ा सेट 41 दांत टॉप पुश रॉड कैंषफ़्ट ब्रिज टीथ रॉकर शाफ्ट 125/150 मोटरसाइकिलों के साथ संगत
The CG125 camshaft three-piece kit is a dedicated maintenance/replacement kit for the rocker arm-type valve mechanism, integrating the camshaft, bridge gear, rocker shaft and seals. It is used to address issues such as camshaft wear and valve timing disorders, and is compatible with the Honda CG125 ...
CG125 मडगार्ड मध्य खंड काला ABS रियर मडगार्ड कनेक्टिंग कवर 125 टॉप-बार मोटरसाइकिल रियर व्हील मडगार्ड मध्य खंड के लिए उपयुक्त
The CG125 middle fender section matches the installation clips and connecting grooves with the upper and lower sections of the CG125 rear fender 1:1, allowing direct replacement of the original middle fender without modification. It is made of high-strength ABS engineering plastic through injection ...
CG125 वाल्व, मूल फ़ैक्टरी विनिर्देश, वाल्व सीट रिंग के साथ कसकर फिट बैठता है
The CG125 uses a single-cylinder, two-valve (1 intake, 1 exhaust) OHV (overhead valve with pushrod) valve mechanism. The valve assembly is the core of the engine's valve system, responsible for accurately opening and closing the intake and exhaust channels according to the engine cycle, ensuring the ...
CG125 सिलेंडर सेट, सिंगल-सिलेंडर चार-स्ट्रोक एयर-कूल्ड इंजन की मुख्य असेंबली
The CG125 cylinder set is the core assembly of a single-cylinder, four-stroke, air-cooled engine, used in 125cc commuter motorcycles. It consists of a cylinder body, piston, piston rings, piston pin, circlip, and upper and lower gaskets, responsible for completing the four-stroke cycle of intake, ...
CG125 मॉडल के लिए 5-छिद्र 6-प्लेट क्लच
5-hole 6-plate clutch for CG125 model High-performance 5-hole 6-plate clutch assembly specifically designed for CG125 motorcycle models. This precision-engineered component ensures optimal power transfer and durability. 5-hole mounting pattern for secure installation 6-plate design for enhanced ...
CG125 पीछे के पहिया विधानसभा 1.6×18 इंच रिम हब स्पोक सेट
CG125 rear wheel assembly, size 1.6×18 inches, axle diameter and sprocket mounting position perfectly match CG125 rear axle and transmission system, compatible with Honda CG125, Pearl 125 and other 125cc pushrod models, can directly replace the original rear wheel without modification; made with ...
CG125 फ्रंट व्हील हब असेंबली एल्यूमीनियम फ्रंट व्हील हब संगत 125 टॉप रॉड मशीन फ्रंट व्हील स्पोक हब
CG125 front wheel hub assembly, with axle hole dimensions and spoke hole positions matching the CG125 front axle and rim 1:1, suitable for Honda CG125, Zhujian 125 and other 125cc push-rod engine models, directly replacing the original front wheel hub without modifications; made of high-strength die...
CG125 फ्रंट व्हील असेंबली 1.4×18 इंच रिम हब स्पीक सेट
CG125 front wheel assembly, size 1.4×18 inches, the hole position and axle diameter perfectly match the CG125 front axle; uses Japanese cold-pressed rim, high-precision hub, and galvanised spokes, with the rim roundness pre-calibrated before leaving the factory (error ≤1mm), ready to install, saving ...
